THE INTERNATIONAL JAGUAR 'S'-TYPE REGISTER FORUM

A pleasure. I was editing while you posted. See final pic.

That will help when installing. I asked SNG to check their rubber kit to see if it is included in that kit. Need to make it to the garage, and check the kit that I already bought to see if it is in there.
Thanks

We can talk when you get around to installing but some stretching is inevitable when feeding tongue into slot. It is a bit of a fight. Do not immediately trim to size. Leave for a few weeks & it will shrink a bit. Only then trim or it will be too short. Once trimmed for length put a drop of cyanoacrylate at each end to glue rubber tongue to beading so no further shrink back can take place.

It was not supplied in my rubber kit but things change over time & with supplier.

Glyn Ruck wrote: ↑Sun Dec 16, 2018 5:53 pm Huh! you are in luck. Found a piece & deleted my poor representation above. Hope this will help Barratts identify.



IMG_1340.JPG


Profile:


IMG_1312.JPG


Rubber side to beading


IMG_1322.JPG


Velvet Side to glass



IMG_1317.JPG



IMG_1312 - Copy.JPG

SNG says that they do not have it. Do you or anyone know where I can find it.
Thanks,
Joe

Argh! They supplied mine. I suppose they wont say who their supplier was?

None of the usual suspects like Robey or Manners have.

This from John Gordon Jaguar might work but you would need to see a piece of it.

https://www.ebay.co.uk/itm/JAGUAR-DAIML ... xyuCJRc80K

I would fire an inquiry to Bains

https://coh-baines.co.uk/

I'll keep looking. Woolies have a product but it does not have the correct tongue profile so you would have to glue it in place.

Glyn,
I contacted both in your last post. Let's see if they respond.
Thanks so much,
Joe

Joe ~ more research,

I'm told on good authority that Part Number BD46440/1 JAGUAR DAIMLER OUTER DOOR GLASS WINDOW SEAL FITS the list below (It looks as if it will do the job ~ It's almost identical to 2179)



420 Saloon
Daimler 2.5 V8 / V8 250
Daimler Hearse
Daimler Limousine
Daimler Sovereign
Mk X / Mk 10 3.8
Mk X / Mk 10 4.2, 420G
S-Type 3.4, 3.8
XJ12 S3
XJ6 S2 / Daimler Sovereign S2
XJ6 S3
XJS


David Manners also has stock of BD46440/1

http://www.jagspares.co.uk/Manners/part ... 440%2F1%2A

And guess what ~ so does SNG Barratt. They have lost the cross-read/reference on their new website.

https://www.sngbarratt.com/uk/#!/Englis ... d6b2a3c83c

Glyn,
Great job....thanks so much. The ebay guy got back to me and said his would fit, but I contacted SNG and educated them and ordered two from them. Thanks so much,
Joe

Joe ~ I don't know how Barratts is selling the stuff but you will need 4 pieces. One for each door winding window. When they supplied me it was in one continuous piece off of a bulk roll. Just make sure that they send you sufficient to do all 4 winding windows.

There are small errors in the parts manual. Another for the S Type is the thermostat. The thermostat P/N in the parts manual is wrong. The picture is correct but the P/N wrong. The S Type needs a shrouded thermostat to cool properly.

See from post #7 here to save me repeating.

https://www.jaguarforums.com/forum/mki- ... nt-208647/


Basically you need this thermostat. P/N C3731/1


NOT this thermostat

Got it on the cap.....have to check to see what I have.

The parts manual says I need two 2179 pieces. I ordered two. Should I get four?

Thanks,